In the Chapter 2, we discussed how a Message Router can be used to decouple a message source from the ultimate destination of the message. This chapter elaborates on specific types of Message Routers to explain how to provide routing and brokering ability to an integration solution. Most patterns are refinements of the Message Router pattern while others combine multiple Message Routers to solve more complex problems. Therefore, we can categorize the Message Routing patterns into the following groups:

• Simple Routers are variants of the Message Router and route messages from one inbound channel to one or more outbound channels.
• Composed Routers combine multiple simple routers to create more complex message flows.
• Architectural Patterns describe architectural styles based on Message Routers.

Simple Routers

The Content-Based Router inspects the content of a message and routes it to another channel based on the content of the message. Using such a router enables the message producer to send messages to a single channel and leave it to the Content-Based Router to inspect messages and route them to the proper destination. This alleviates the sending application from this task and avoids coupling the message producer to specific destination channels.

A Message Filter is a special form of a Content-Based Router. It examines the message content and passes the message to another channel if the message content matches certain criteria. Otherwise, it discards the message. Message Filters can be used with Publish-Subscribe Channel to route a message to all possible recipients and allow the recipients to filter out irrelevant messages. A Message Filter performs a function that is very similar to that of a Selective Consumer with the key difference being that a Message Filter is part of the messaging system, routing qualifying messages to another channel, whereas a Selective Consumer is built into a Message Endpoint.

A Content-Based Router and a Message Filter can actually solve a similar problem. A Content-Based Router routes a message to the correct destination based on the criteria encoded in the Content-Based Router. Equivalent behavior can be achieved by using a Publish-Subscribe Channel and an array of Message Filters, one for each potential recipient. Each Message Filter eliminates the messages that to not match the criteria for the specific destination. The Content-Based Router routes predictively to a single channel and therefore has total control, but is also dependent on the list of all possible destination channels. The Message Filter array filters reactively, spreading the routing logic across many Message Filters but avoiding a single component that is dependent on all possible destinations. The trade-off between these solutions is described in more detail in the Message Filter pattern.

A basic Message Router uses fixed rules to determine the destination of an incoming message. Where we need more flexibility, a Dynamic Router can be very useful. This router allows the routing logic to be modified by sending control messages to a designated control port. The dynamic nature of the Dynamic Router can be combined with most forms of the Message Router.

Chapter 3 introduced the concept of a Point-to-Point Channel and a Publish-Subscribe Channel. Sometimes, you need to send a message to more than one recipient, but want to maintain control over the recipients. The Recipient List allows you do just that. In essence, a Recipient List is a Content-Based Router that can route a single message to more than one destination channel.

Some messages contain lists of individual items. How do you process these items individually? Use a Splitter to split the large message into individual messages. Each message can then be routed further and processed individually.

However, you may need to recombine the messages that the Splitter created back into a single message. This is one of the functions an Aggregator performs. An Aggregator can receive a stream of messages, identify related messages and combine them into a single message. Unlike the other routing patterns, the Aggregator is a stateful Message Router because it has to store messages internally until specific conditions are fulfilled. This mean that an Aggregator can consume a number of messages before it publishes a message.

Because we use messaging to connect applications or components running on multiple computers, multiple messages can be processed in parallel. For example, more than one process may consume messages off a single channel. One of these processes may execute faster than another, causing messages to be processed out of order. However, some components depend on the correct sequence of individual messages, for example ledger-based systems. The Resequencer puts out-of-sequence messages back into sequence. The Resequencer is also a stateful Message Router because it may need to store a number of messages internally until the message arrives that completes the sequence. Unlike the Aggregator, though, the Resequencer ultimately publishes the same number of messages it consumed.

The following table summarizes the properties of the Message Router variants (we did not include the Dynamic Router as a separate alternative because any router can be implemented as a dynamic variant):

Composed Routers

A key advantage of the Pipes and Filters architecture is the fact that we can compose multiple filters into a larger solution. Composed Message Processor or an Scatter-Gather combine multiple Message Router variants to create more comprehensive solutions. Both patterns allow us to retrieve information from multiple sources and recombine it into a single message. While the Composed Message Processor maintains control over the possible sources the Scatter-Gather uses a Publish-Subscribe Channel so that any interested component can participate in the process.

Both the Composed Message Processor and the Scatter-Gather route a single message to a number of participants concurrently and reassemble the replies into a single message. We can say that these patterns manage the parallel routing of a message. Two more patterns manage the sequential routing of a message, i.e. routing a message through a sequence of individual steps. If we want to control the path of a message from a central point we can use a Routing Slip to specify the path the message should take. This pattern works just like the routing slip attached to office documents to pass them sequentially by a number of recipients. Alternatively, we can use a Process Manager which gives us more flexibility but requires the message to return to a central component after each function.

Architectural Patterns

Message Routers enable us to architect an integration solution using a central Message Broker. As opposed to the different message routing design patterns, this pattern describes a hub-and-spoke architectural style.

The Right Router for the Right Purpose

This chapter contains 10 patterns. How can we make it easy to find the right pattern for the right purpose? The following decision chart helps you find the right pattern for the right purpose by matter of simple yes/no decisions. For example, if you are looking for a simple routing pattern that consumes one message at a time but publishes multiple messages in sequential order, you should use a Splitter. The diagram also helps illustrate how closely the individual patterns are related. For example, a Routing Slip and a Process Manager solve similar problems while a Message Filter does something rather different.

Find the full description of this pattern in: Enterprise Integration Patterns Gregor Hohpe and Bobby Woolf ISBN 0321200683 650 pages Addison-Wesley	From Enterprise Integration to Enterprise Transformation: My new book describes how architects can play a critical role in IT transformation by applying their technical, communication, and organizational skills with 37 episodes from large-scale enterprise IT. DRM-free eBook on Leanpub.com Print book on Amazon.com
Parts of this page are made available under the Creative Commons Attribution license. You can reuse the pattern icon, the pattern name, the problem and solution statements (in bold), and the sketch under this license. Other portions of the text, such as text chapters or the full pattern text, are protected by copyright.

Messaging Patterns » Message Routing » Introduction to Message Routing

Previous   Next